Blowing sanding dust off your wood project with an air compressor or brushing it onto your floor can still result in it ending up in your wet stain or finish. Instead, use a bristle attachment on a vacuum to safely capture it once and for all. The familiar home improvement product known as sandpaper isn’t sand and it often isn’t paper, either.

For whatever reason, I typically have to purchase from a different brand every time I buy new sandpaper – the one I purchased previously is usually no longer available. Either way, I haven’t bought anything terrible yet, so I’m still recommending you get the paper online. A 10-pack of 3M Hook and Loop Sandpaper costs about $10 at posting. I always wear my heavy-duty mask when I’m sanding for this reason. I have this mask from Amazon, and it does a great job at keeping the dust out.

sandpaper for wood

The Milady brand sandpaper is very convenient, it offers excellent value for the most durable sandpaper on the market. This all in one assorted grit sandpaper is suitable for finishing all your needs. It is an excellent choice for buffing and polishing your woodwork, metal, automotive, and plastic applications. The heat from the sun can cause moisture in the wood to create bubbles in your stain or finish. During the entire recommended drying time listed on the label. If the temperature drops, the evaporation process will slow and the wood preparation product will remain tacky for a longer length of time.

What Is 220 Grit Sandpaper Normally Used For?

Keep in mind that rough grits of sandpaper leave deep scratches, so start with the finer grits and slowly work up to the rougher grades. Medium or grit sandpaper is good for sanding bare wood in preparation for finishing and for the gentle removal of varnish. Moving a random orbit sander too quickly will create “pigtails” on the surface of your wood. They’re not cute — and you’ll never know when to stop sanding. However, if you move the sander only one inch per second, you only need to go over each area ONCE.

sandpaper for wood

You’ll notice a trend here of a recommendation to start with a lower number grit and work your way up. Except, of course, if your only goal is rapid removal of wood and the finish isn’t https://ronbaileyscarvings.com/ important. Well, one example is grinding cabinet filler strips to fit the wall. I do prefer, though, to at least consider pairing a 150 and 220 grit together while doing finish sanding.

How Do I Choose Sandpaper For Wood?

Use Blue Scotch 3M Painters masking tape to section off your project. Great for two tone finishes or for creating specialty looks such as this checker board pattern. Small old bristle brush for dragging excess stain or paint out of corners. Flimsy foam brushes fall apart in minutes – a good foam brush can be used several times. We usually have several either in use, rinsed or drying. They can be stored after drying and reused several times.

  • Also, sand areas where the pressure washer lifted the wood grain.
  • When using wet/dry sandpaper to sand wood, use a light touch so as not to clog the paper with wood dust too quickly.
  • It is excellent sandpaper for those who are looking for sandpaper at a low price with high quality.
  • Materials used to make sandpaper include aluminum oxide, ceramic, flint, garnet and silicon carbide.
  • If you’ve bought inexpensive softwood, you’ll probably want to start with the lowest grit you have to remove any manufacturing marks, stains, or flaws.
  • It may take more time than sanding veneer since you must wait until each layer of lacquer dries completely before you can begin sanding it.

Shown here is an orbital power sander with dust bag used to prep the wood surface and buff out between top coats. Just use the correct grade of sandpaper when buffing out between top coats or milk paints. Do not use an orbital sander when distress sanding flat painted surfaces for an antiqued look. The orbital sander will dig in as you apply pressure to get through the paint, leaving round areas of wear that will not look natural.

Sanding a piece might take just two grits or you might have to work through 4 or 5 to get to the finish that you want. By now you probably understand that you start with a lower grit and work your way to higher grits. So, to help you out, here’s my general progression for hardwoods https://ronbaileyscarvings.com/sandpaper-for-woodworking/ and softwoods lumped into three categories. First, if your wood was glued together it’s likely uneven and you’ll want to run it through a planer or a hand plane. While I often use a 24-grit in my drum sander, it’s because I don’t like the risk of chip-out from a planer.

Since wood pores are irregular, use Minwax® Pre-Stain Wood Conditioner before you stain to reduce the likelihood of blotchiness. For beginners and experienced DIYers, our checklist will take any paint job from “good” to “amazing.” Get it free when you sign up for our newsletter. Non-Woven abrasives are color-coded go to indicate their different grits. They use industry standard colors and most manufacturers of non-woven abrasives conform to this Standard. $0.00Order subtotal does not cover discounts and extra costs like shipping charges, etc. The final cost of the order will be calculated at the checkout page.